TMK Tees

How to Wash Custom Printed T-Shirts Without Fading

How to Wash Custom Printed T-Shirts Without Fading — key points at a glance
How to Wash Custom Printed T-Shirts Without Fading — key points at a glance

Most custom tees don't fade in the printer. They fade in the washing machine. A single 60°C wash can crack a print that would otherwise last five years.

Short answer: wash custom printed t-shirts inside out at 30°C on a gentle cycle, then air-dry on a hanger. That single habit prevents the vast majority of print damage across DTG, screen print, and heat transfer methods.

Start With These Three Steps

Turn it inside out. The drum of a washing machine abrades whatever faces outward. Over 30 or 40 cycles, that friction breaks down ink layers. Inside out, the fabric takes the wear, not the print.

Wash at 30°C, never hotter. Heat degrades plastisol inks (the standard type in screen printing) and weakens the bond between DTG ink and cotton fibres. Cold is always safer than hot. This also applies to the blank itself: a quality piece like a Gildan Ultra Cotton T-Shirt holds its shape far better below 40°C.

Skip the tumble dryer, or use its lowest heat setting. Hang the garment on a wide-shouldered hanger to air-dry. This protects both the print and the neckline.

Does the Print Method Change the Care?

Yes, though the differences are small. Screen-printed tees are the most forgiving: plastisol ink cures into a hard film on the fabric surface and handles washing well. DTG ink penetrates the fibres, so it needs slightly gentler conditions. Heat transfer and vinyl prints are most vulnerable to heat at every stage.

Print method Max wash temp Tumble dry? Iron over print?
Screen print 40°C Low heat only No
DTG 30°C No, air-dry No
Heat transfer / vinyl 30°C No No

One specific tip for DTG: skip fabric conditioner for the first three washes. Conditioner coats fibres and can interfere with the ink's bond to the cotton during the initial cure period. After that, it is fine to use.

What About Detergent?

Standard detergent, biological or non-biological, makes little difference to print longevity. Bleach, however, destroys colour on every print type without exception. Never use it on a printed garment.

For heavier pieces like a custom hoodie, a colour-protect formula helps maintain the depth of the base fabric dye alongside the print. The Gildan Heavy Blend Hoodie is one of the most popular blanks for custom streetwear printing; washing it with a colour-protect detergent keeps the fabric looking fresher after repeated washes.

Follow these steps consistently and a well-printed tee will hold its design for 50-plus washes. The print is not the weak point. The wash cycle is.

Affiliate disclosure: some links on this page are affiliate links. TMK Tees may earn a small commission if you buy via these links, at no extra cost to you.

Related Products

Gildan Ultra Cotton T-Shirt

A go-to blank for DTG and screen printing, available in 30-plus colours. Holds print well after repeated washes.

View on Amazon UK →
Gildan Heavy Blend Hoodie

A popular blank for custom streetwear. 50/50 cotton-polyester blend handles screen print and embroidery reliably.

View on Amazon UK →
Fruit of the Loom Classic Hoodie

An affordable, wash-durable blank for personalised hoodies and branded streetwear drops.

View on Amazon UK →

FAQ

Can I put a custom printed t-shirt in the tumble dryer?

You can, but only on the lowest heat setting, and remove the garment while it is still slightly damp. High heat is the fastest way to crack or peel any type of print, regardless of method. Air-drying is always the safer option.

Why does my DTG print feel stiff after the first wash?

Some stiffness is normal after the first wash; DTG prints soften with each subsequent cycle. If the stiffness persists after four or five washes, the garment may have been under-cured during production.

Can I iron a custom printed t-shirt?

Yes, but never directly over the design. Turn the garment inside out and iron from the reverse side, or place a thin cotton cloth between the iron and the print. Direct heat from an iron will melt or warp most print types.

How many washes should a custom tee last?

A well-printed tee on a quality blank, washed at 30°C inside out and air-dried, should hold its print for at least 50 washes. Screen prints on 100% cotton typically last the longest. DTG prints on cotton-polyester blends tend to fade faster than on pure cotton.

Does washing inside out actually make a measurable difference?

Yes. Inside-out washing reduces direct abrasion against the printed surface and limits contact between the ink layer and other items in the drum. For printed garments specifically, it also prevents colour transfer from other items onto the face of the design.

Privacy · Terms · Cookies · Affiliate disclosure